Firmapress Pigułka Mix
Firmapress to uniwersalna, wielofunkcyjna substancja wiążąca, która współdziała z 99% produktów, których możesz potrzebować do produkcji skutecznych tabletek. LFA stworzyło ten produkt, aby ułatwić proces tworzenia tabletek, a każde składnik przyczynia sie do wyjątkowych właściwości mieszanki. Zawiera mikrokrystaliczną celulozę, stearynian magnezu, ditlenek krzemu i wodorofosforan wapnia.
Connect with Our Team
If you have a question or would like more details on the Firmapress Pigułka Mix, please complete the form below and someone from our team will be in touch with you soon.
Te składniki charakteryzują wszystkie cechy, które są konieczne do stworzenia skutecznych tabletek wysokiej jakości. Firmapress usuwa stres związany z wyszukiwaniem i tworzeniem mieszanki, która przyniesie oczekiwane rezultaty, pozwalając tym samym zaoszczędzić czas i energię, które można zainwestować w dobór składników do kolejnej mieszanki. Oto czego możesz spodziewać się po Firmapress:
- Duża przepływność
- Silne właściwości wiążące
- Lubrykant
- Pochłanianie cieczy
- Wydajny wypełniacz
Poniżej dowiesz się, w jaki sposób każdy składnik dodaje mieszance Firmapress skuteczności:
Celuloza mikrokrystaliczna: Celuloza mikrokrystaliczna to proszek o dużej przepływności, który dodaje wagi i objętości tabletce. Posiada silne właściwości wiążące przy jednoczesnym zachowaniu wysokiej przepływności, dzięki czemu jest równomiernie rozprowadzany w mieszance. Ponieważ jest obojętny chemicznie, nie wejdzie w reakcję z innymi składnikami. To przydatny składnik, który ułatwia każdy etap procesu tworzenia tabletek.
Stearynian magnezu: Magnez to główny lubrykant w całej mieszance. Podczas produkcji zmniejsza tarcie w miejscach styku powierzchni tabletki z głowicą, dzięki czemu zmniejsza prawdopodobieństwo ewentualnego uszkodzenia tabletki. Zapobiega przywieraniu mieszanki do urządzenia i nie mają na niego wpływu zmienne procesowe ( np. przepływ, temperatura, ciśnienie i poziom), które zachodzą spontanicznie. Stearynian magnezu sprawia, że niespodziewane zdarzenia nie wpłyną na proces produkcyjny. Podobnie jak celuloza mikrokrystaliczna cechuje go duża przepływność i jest obojętny chemicznie.
Ditlenek krzemu: Ditlenek krzemu z łatwością pochłania wilgoć, zamieniając ciekłe składniki w sypki proszek, który można dodać do mieszanki. Działa jako lubrykant, który poprawi przepływność, a jednocześnie przyspiesza proces produkcji tabletek. Zmniejsza również ilość wilgoci, która z czasem może spowodować uszkodzenie urządzeń.
Difosforan wapnia: Popularny wypełniacz, sprawia, że tabletki mają taką samą zawartość składników i zwiększa ich możliwości kompresyjne. Innymi słowy, pozwala z łatwością ukształtować i scalić tabletki.
Powyższe proszki cechuje duża przepływność i są chemicznie obojętne, z wyjątkiem difosforanu wapnia, którego nie powinno się łączyć z aktywnymi kwasami. To ułatwia i przyspiesza dobór kompatybilnych składników. Każdą mieszankę wzbogacą o dodatkowe zalety i sprawią, że proces produkcyjny będzie przebiegał sprawnie. Pozwól nam zająć się stroną techniczną, abyś mógł skoncentrować się na ulepszaniu reszty mieszanki. Nasz produkt barwimy środkami do farbowania żywności i oferujemy szeroką gamę kolorów, spośród której możesz wybrać ten, który Tobie odpowiada. Oferujemy darmową dostawę.
Nazwa | WartoÅÄ |
---|---|
Forma | BiaÅy/kolorowy proszek |
Stan fizyczny | StaÅy |
Przechowywanie | PrzechowywaÄ w temperaturze pokojowej |
Podatny na bezpoÅrednie Åciskanie | Tak |
Net Weight (kg) | 1.06 |
Yes, it does not matter what age, size or sex the person consuming the products is. It is, however, important to check the intolerance data.
Yes, all of the excipients are safe for human or animal consumption. There are some precautions that should be taken when handling them and there are some people that might have intolerances to some of them. Information on this can be found in the products MSDS and Intolerance Data Sheet. This can be found in this section for every excipient.
Yes, there are all of them can be found in the intolerance sheets for each product. The intolerance sheets can be found here: https://www.lfatabletpresses.com/product-data
FFFFFF No, sorry we are simply not able to make the colours. We do not have access to the pigments.
Yes, if you have an active ingredient that has particular issues then it is ok to add other excipients to help accommodate and fix the issue.
Yes, it works extremely well with any shaped die or tooling set. It is also designed to be able to get a clean print with tooling that has images, letters or numbers on it.
Yes, we have bulk pricing for all of our excipients, and these can be found in this section. We offer bulk in 500 kg, 1 ton, 2 ton and 5 ton lots. The prices are set on these quantities as these are the amounts that will fit on pallets.
Yes. CoA stands for Certificate of Analysis this is also known some times as an MSDS (Material Safety Data Sheet) all of the information contained in a CoA is inside the MSDS for every LFA product which is emailed to you after purchase.
To mało prawdopodobne, aby produkcja tabletek bez dodatku substancji pomocniczych była możliwa. Niektóre substancje mogą wiązać się bez dodatku substancji pomocniczych, jednak nie będą w stanie przejść przez tabletkarkę. Zalecamy stosowanie gotowej mieszanki Firmapress Pigułka Mix, która łączy się z 99% substancji.
Yes. However, there is a minimum order of one batch, which is 1 ton, and there is a 4 week lead time.
If this is something that a customer is interested in, then they need to put down a non-refundable deposit of $1000 for us to start formulating. They also need to provide us with the exact panton colour.
Yes. There are two things at play here. You can get hygroscopic and hydrophobic excipients. Hygroscopic means that they take on water quickly, while hydrophobic means that they repel water.
There are products know as supper disintegrants. These products help the breakdown of tablets. At the moment LFA does not sell any supper disintegrants.
Magnesium stearate is hydrophobic this means that it will slow the breakdown of a tablet.
However, it is used in such small amounts that most of the time it will not make a difference to our customer's products. If they would like to be sure then they should conduct what is known as a disintegration test.
Yes, we do, as far as we know there are no products in Firmapress that require any form of registration any ware in the world.
However, we would recommend that you check with your local authorities before ordering for the first time. Note: We have had problems shipping the product to Brazil. We tend to find the customs can seize the product.
It is not illegal in Brazil but the customer needs a freight agent that has experience in this area to clear it through customs.
No, Firmapress is designed to be soft on the tooling and not stick to its surfaces. It can be used with any metal or coating.
No, we have specifically avoided lactose because a number of people are what is known as lactose intolerant. Lactose intolerance can cause abdominal pain, bloating and other symptoms.
Thermal gelation is where a powder in water becomes a jelly once heated. This can happen with MCC but we can not guarantee it with Firmapress due to all of the other products in it.
Yes, it is totally harmless to animals as well as humans. It can be used in any products.
9 years, it was first developed by LFA to help a customer out with there tablet formulation. It has been modified a few times to get to what we have today.
Firmapress - 2 years form batch date.
Dextrose - 3 years from batch date.
Dicalcium Phosphate - 3 years from batch date.
Microcrystalline Cellulose -
Magnesium stearate -
Lactose - 2 years from batch date.
Silica Dioxide - 2 years from batch date.
here are 6 steps that should be followed as a general rule of thumb when cleaning contact surfaces that have come into contact with powders:
Dry Clean - First you need to remove as much of the dry powder as possible. You can do this using a hover/vacuum. Make sure that the vacuum you are using has a filter good enough to handle fine dust.
Wet Clean - Next you need to perform a wet clean. This can be done with warm water and soap or if available an ultrasonic cleaner.
Rinse - Next you need to rinse off any soap with potable water (drinking water). You do not have to do this if you used an ultrasonic cleaner in the last step. It is important to ensure that all parts are thoroughly dried immediately after washing to avoid any rusting.
Sanitise - Next you need to sanitise the surface. This step is recommended by the FDA. There are a number of sanitising solutions available designed to be applied and left on.
Lubricate - You now need to lubricate any parts that require it. This should be with the appropriate grade oil or grease considering your use and greasing chart. Store - Finally store any of the parts in a cool dry place. If you are storing them on the machine then make sure the machine is in a temperature controlled environment with low humidity.
Firmapress is extremely hygroscopic. This means that it very easily absorbs water and moisture. This includes the water content in the air.
If water is spilled onto Firmapress, or if a bag is left open for an extended period of time, then the Firmapress needs to be thrown away.
While it is possible to dry the Firmapress out, it is likely that two things will have happened:
- The structure of the Firmapress will have changed so it does not bind as well any more.
- Bacteria may have been introduced into the Firmapress, rendering it no longer safe for use in human or animal products.
Yes, when LFA first launched Firmapress for a short while it was called Ready Mix.
Now however it is called Firmapress and it is a trademarked term because of this it is really important that you only use the term Firmapress and that you correct customers whenever they ask.
Yes, there are no traces of gluten in any of the ingredients used to make Firmapress.
Yes, Firmapress is Vegan and Vegetarian. All of the products used to make it are free from animal products.
No not essential but highly recommended. It will depend on the accuracy that you require.
This will depend on things like the LD50, your quality control systems and a number of other factors.
Because of this, it is a decision that you have to make. Firmapress should not be put in a blender or a mill. It will affect the composition and will no longer bind as well.
No, sorry, we only offer 1kg bags.
No, it is completely taste free. It should not, however, be used for chewable tablets.
It would be very gritty to chew on. For a chewable tablet, we recommend dextrose or lactose as a binder.
We use a product called Aluminum Lakes. You can share this with customers.
We use FD&C Aluminum Lake's these are pharmaceutical grade and regulated by the FDA.
No, sorry we are not able to refund any Firmapress that has been opened. We strongly recommend that you buy a 1kg sample of Firmapress first to test your product and only then buy a bigger amount.
While the bag remains sealed, Firmapress is fairly resilient.
Do not expose it to extreme temperatures below -5 °C or higher than 40 °C. Once opened, Firmapress needs to be stored in clean, dry conditions between 10 and 30 °C. Once a bag is opened, if it is not all used, then make sure the bag is closed securely. With 1 kg and 5 kg bags, this can be done using the grip seal at the top. For 25 kg sacks use a couple of cable ties.
Dextrose - approx 100 mesh
Dicalcium Phosphate - approx 100 mesh
Microcrystoline Cellulose - approx 120-200
Magnesium sterate -
Lactose - 80 mesh
Silica Dioxide -
Firmapress - 100-200 mesh
20%. If you go much below this % then you might need to add extra lubricants. However, this is very dependent on the product being pressed. If the product being pressed is not at all sticky and only needs a little bulking out it could be less but this would be very rare. Most of the time you will need to use between 30-60%
Dextrose - Sweetener, binding agent, good for chewable tablets or candy.
Microcrystalline Cellulose - Binder, filling agent. Good at binding tablets and making them bigger. It can also be used as a filler for capsules.
Magnesium stearate - Dry Lubricant. This stops products from getting stuck to the tooling. It can also help with powder flow issues and caking issues.
Lactose - Binder, sweetener and bulking agent. It has a large mesh so it flows well but most people do not like it because of the intolerance issues.
Silica Dioxide - Flowing agent. This assist powders in flowing smoothly through the machines. It also helps with cacking issues where powders get stuck to the machine.
Firmapress - 2 years form batch date.
Dextrose - 3 years from batch date.
Dicalcium Phosphate - 3 years from batch date.
Microcrystalline Cellulose -
Magnesium stearate -
Lactose - 2 years from batch date.
Silica Dioxide - 2 years from batch date.
There are 3 things that we would recommend trying: Increase the amount of Firmapress in your mix.
This will reduce the % of the active in the total mix and give the dry lubricants a better chance to work. Try granulating your mix.
This will reduce the surface area of your active and allow the dry lubricants in Firmapress to coat them better. Try using coated tooling. Changing your tooling for a set that has a coating you can reduce the ability for powders to stick to them. More information on this can be found in the tooling FAQ.
The bulk density of Firmapress is and is listed on the website and in this section of the website.
The bulk density of an item is when it is loose. Once it has been pressed into a tablet this will change.
You are not able to calculate the weight of a tablet based on the shape and the tablet and the powders used as it is also affected by the pressure and the fill depth that the press is set to.
If your product does not bind well then we would recommend using MCC. This can be used in any % the limiting factor is the size of the tablet.
If the amount of MCC you would have to use would be too much or if you do not want to use MCC then you have 3 other options: Ask your supplier for a directly compressible or tabletable grade of your product. Spray dry your product. Wet granulate your product.
If your product is sticky then you will need to add a dry lubricant to your mix. For this, we recommend magnesium stearate.
We do not recommend that you add more than 1% to the mix as more than this can cause capping. If your product is still sticky at this point then we would recommend looking into granulation.
If your product or API is clumpy then you will need to add an anticaking agent. For this, we recommend silicon dioxide. We only recommend adding a maximum of 2% of this to the mix
It is very likely to work with it yes. We believe that Firmapress works with 99% of products that we have tried.
The most important point is at what point will it work. If you need a 300mg caffeine tablet with a total tablet weight of say 350mg then it is fairly unlikely that there will be enough of the flowing agent to be able to pull the caffeine powder through the feeding system.
This is because caffeine powder can be quite “fluffy”. If however, you are working with a granulated version of caffeine then there is a fairly good chance it will work. It really is just at what ratio it is able too.